KCCS
Precision Timing
Soluciones de sincronización de precisión para las industrias y entornos más exigentes.
Los osciladores KCCS están diseñados y calificados para aplicaciones donde los errores de sincronización se traducen directamente en pérdida de rendimiento del sistema. A continuación se muestra cómo nuestra línea de productos se mapea a entornos reales de despliegue — cubriendo las restricciones técnicas que los ingenieros realmente enfrentan, no afirmaciones de marketing.
Design challenge: On-board timing must survive launch vibration, rapid thermal cycling in low-Earth orbit, and long operational life (5-7 years) with no ground support. Phase noise contributions couple directly to carrier recovery in transponder downlinks.
Recommended products: KONB27 (low phase noise OCXO, -168 dBc/Hz @1 kHz), KOR series (vibration-resistant, ≤0.05 ppb/g), KCPTA50 (CPT atomic clock, ≤3 W, autonomous holdover).
Design challenge: Ocean bottom nodes spend months unattended at 3000m depth. Timing drift between nodes introduces position error in migration velocity analysis. Power budgets are tight—every mW extends battery life between recovery campaigns.
Recommended products: KOP15 (low-power OCXO, 130 mW steady-state), KDO9 (micro disciplined, 12.5×9×2.5 mm), KOM07 (SMD OCXO, 9.7×7.5×3.9 mm).
Design challenge: Cellular base stations need holdover when GNSS is jammed or obstructed. PTP (IEEE 1588) boundary clocks require stratum-3e stability. Power and board area constrain remote radio units.
Recommended products: KT05 (TCXO, ±0.05 ppm, 7×5 mm), KDO27 (disciplined OCXO, ±1.5 μs/24 h), KPLO38 (PLO, -160 dBc/Hz @1 kHz).
Design challenge: High-frequency trading firms and AI training clusters require nanosecond-level timestamp accuracy across thousands of servers. PTP grandmasters need disciplined references that survive timing packet loss. AI accelerator cards demand low-jitter reference clocks for PCIe Gen5/6 SerDes.
Recommended products: KOT50 (ultra-high stability OCXO, ±0.01 ppb), KCSA35 (CSAC, ±1E-12/24 h), KV09 (VCXO, <0.5 ps RMS jitter).
Design challenge: Coherent radar systems need extremely low close-in phase noise to resolve small targets in clutter. Vibration platforms (vehicles, aircraft, naval) impose G-sensitivity requirements that off-the-shelf OCXOs cannot meet without redesign.
Recommended products: KONA50 (-170 dBc/Hz @1 kHz), KOR25/KOR38 (vibration-resistant, ≤0.1 ppb/g), KRA76 (rubidium, long-range radar reference).
Design challenge: Phasor measurement units (PMUs) require UTC traceable timing with sub-microsecond accuracy over decades of service. Temperature-induced drift across outdoor substations (-40~+85℃) directly impacts state estimation accuracy.
Recommended products: KOT25 (±0.2 ppb across -40~+105℃), KDO65 (disciplined, ±1.5 μs/24 h), KCPTA50 (CPT, ±5E-11 across -40~+80℃).
Design challenge: On-board navigation payloads need radiation-tolerant timing references with proven long-term stability. Rubidium frequency standards have a 30+ year flight heritage in GPS and Galileo satellite payloads.
Recommended products: KRA50/KRA94 (rubidium oscillators), KCPTA50 (CPT for smaller satellites), KOT20 (DIP 20×20 mm, compact OCXO).
Design challenge: Signal generators, spectrum analyzers and frequency counters need reference oscillators with phase noise lower than the DUT under test. Calibration labs need rackmountable rubidium or OCXO references with traceable stability data.
Recommended products: KONS450 (8E-14 @10s ADEV), KONA50 (-170 dBc/Hz), KRA50 (rubidium, 10 MHz sine).
Design challenge: Broadcast studios and playout centers sync to black-burst or 10 MHz references. Genlock clocks drift introduces lip-sync errors. Outside broadcast vans need rugged, temperature-stable references.
Recommended products: KOT27 (±0.1 ppb), KDO27 (disciplined, GNSS locked), KRA50 (rubidium studio reference).
Design challenge: Small UAVs and battery-powered IoT end nodes need timing references that work from a single Li-ion cell. Vibration from motors demands G-sensitivity characterization. GNSS-denied operation requires autonomous holdover.
Recommended products: KOM05 (SMD 7.5×5.5×3.3 mm), KOP27 (low-power, 33 mA steady), KCSA35 (CSAC, 130 mW).
Design challenge: MRI gradient amplifiers, CT gantry rotation and laser spectroscopy require stable, low-phase-noise clocks. Patient monitoring equipment needs long-term frequency stability that drifts minimally over years of operation.
Recommended products: KOT25 (±0.2 ppb), KONS327 (ultra-low ADEV), KT05 (TCXO, ±0.1 ppm).
Design challenge: Automotive radar, V2X and industrial PLCs need AEC-Q200 qualified timing across -40~+105℃. Production volume demands low cost with consistent quality.
Recommended products: KT05 (TCXO, G-sensitivity ≤±0.3 ppb/g), KV09 (VCXO, ±20 ppm), KDO5 (disciplined, 7×5×3 mm).
Design challenge: Clock jitter modulates the audio output as audible sideband noise. Reference DACs and digital transports need master clocks quieter than generic XOs.
Recommended products: KONB27 (-168 dBc/Hz), KONS327 (10 MHz master), KV09 (<0.5 ps RMS jitter).
Nuestro equipo técnico le ayuda a elegir el oscilador óptimo.